Communications - Scientific Letters of the University of Zilina 2000, 2(3):15-19 | DOI: 10.26552/com.C.2000.3.15-19

Heat distribution when titanium alloy vt9 grinding

Dusan Steklac1, Miroslav Neslusan1
1 Department of Technological Engineering, University of Zilina, Slovak Republic

Heat distribution in machining is one of phenomenological characteristics of this process because it significantly influences functional properties of machined surfaces. The paper deals with heat distribution in the cutting zone when grinding titanium alloy VT9 based on experimental measurement of surface temperature and tangential component of cutting force. Heat distribution when grinding titanium alloy VT9 differs from heat distribution when grinding conventional roll bearing steel 14 209.4 as a typical representative of ground hardened steels first of all because of low heat conductivity of titanium alloys.

Keywords: no keywords

Published: September 30, 2000  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Steklac, D., & Neslusan, M. (2000). Heat distribution when titanium alloy vt9 grinding. Communications - Scientific Letters of the University of Zilina, 2(3), 15-19. doi: 10.26552/com.C.2000.3.15-19
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. ZLATIN, N. - FIELD, M.: Procedures and Precautions in Machining Titanium Alloys, Titanium Science and Technology, 1 1973, p. 489-504. Go to original source...
    2. KAHLES, J. F. - FIELD, M. - EYLON, D. - FROES, F. H.: Machining of Titanium Alloys, Journal of Metals, IV 1985, p. 27 - 35. Go to original source...
    3. ROWE, W. B. - BLACK, S. C. - MILLS, B. - QI, H. S. - MORGAN, M. N.: Experimental Investigation of Heat Transfer in Grinding, CIRP 44/1/1995, p. 329-332. Go to original source...
    4. KATO, T. - FUJII, H.: Energy Partition in Convetional Surface Grinding, Journal of Manufacturing Science and Engineering, 121/1999, p. 393-398. Go to original source...
    5. JEAGER, J. C.: Moving Source of Heat and the Temperature at Sliding Contact, Proc. of the Royal Society of New South Wales, 76/1942, p. 203-224. Go to original source...
    6. PEKLENIK, J.: Ermittlung von geometrischen and physicalischen Kenngrossen fur die Grundlagenforschung des schleifens, PhD. Thesis, 1957, Aachen.
    7. GU,D. Y. - WAGER, J. G.: New Evidence on the Contact Zone in Grinding, CIRP 37/1/1988, p. 335-338. Go to original source...
    8. ROWE, W. B. - PETTIT, J. A. - BOYLE, A. - MORUZZI, J. L.: Avoidance of Thermal Damage in Grinding and Prediction of the Damage Treshold, CIRP 37/1/1988, p. 327-330. Go to original source...
    9. VASILKO, K. - BOKUČAVA, G.: Brúsenie kovových materiálov, ALFA Bratislava 1988.

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content