Communications - Scientific Letters of the University of Zilina 2000, 2(3):20-29 | DOI: 10.26552/com.C.2000.3.20-29

A new method for durability dependance of a cutting tool on a cutting speed

Karol Vasilko1
1 Faculty of Production Technologies, Technical University of Kosice, with the seat in Presov, Slovakia

In the entire history of the development of the metal cutting theory Taylor's whhich appeared in 1905, has been used to describe the relation between a cutting tool durability and a cutting speed. This relation was established in 1905. This work presents the analysis of the up to now attempts carried out to improve the mentioned relation. The submitted proposal results in the method of creation of the Tvrelation, which provides a much better identity with the experiment. In the second part of the work the method is verified experimentally on aseries of experimental results.

Keywords: no keywords

Published: September 30, 2000  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Vasilko, K. (2000). A new method for durability dependance of a cutting tool on a cutting speed. Communications - Scientific Letters of the University of Zilina, 2(3), 20-29. doi: 10.26552/com.C.2000.3.20-29
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BÉKÉS, J.: Inžinierska technológia obrábania kovov. Bratislava Alfa, 1981, 398 s.
    2. BUDA, J., SOUČEK, J., VASILKO, K.: Teória obrábania. Bratislava Alfa, 1988, 391 s.
    3. DMOCHVSKI, J.: Podstawy obróbki skawanijem. Warszawa. Państwowe wydawnictvo naukowe, 1987, 586 s.
    4. GIĽMAN, A. M.et all.: Optimizacija režimov obrabotki na metallorežuščich stankach. Moskva: Mašinostrojenije, 1975, 304 s.
    5. GRANOVSKIJ, G. I., GRANOVSKIJ, V. G.: Rezanije metallov. Moskva: Mašinostrojenije, 1975, 304 s.
    6. KĽUŠIN, M. I.: Obobščennyje zavisimosti dlja razčeta režima rezanija. In: Fizika rezanija metallov. AN Armenskoj SSR, Jerevan, 1971
    7. LARIN, M. N.: Osnovy frezerovanija. Moskva. Mašgiz, 1947
    8. PODURAJEV, V. N.: Avtomatičeskije regulirujemyje i kombinirovannyje processy rezanija. Moskva: Mašinostrojenije, 1977, 302 s.
    9. VASILKO, K., HRUBÝ, J., LIPTÁK, J.: Technológia obrábania a montáže. Bratislava: Alfa, 1991, 494 s.
    10. VASILKO, K., BOKUČAVA, G.: Presnejšie vyjadrenie T-v závislosti. Náradie 19, 1989, č. 4
    11. ZOREV, N. N.: Metod opredelenija optimaľnogo iznosa i optimaľnoj stojkosti po krivym iznosa. Stanki i instrument, 1949, č. 8.

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content