Communications - Scientific Letters of the University of Zilina 2015, 17(3):57-61 | DOI: 10.26552/com.C.2015.3.57-61

Barkhausen Noise Emission in Milled Surfaces

Miroslav Neslusan1, Tomas Hrabovsky1, Maria Cillikova1, Anna Micietova1
1 Department of Machining and Manufacturing, Faculty of Mechanical Engineering, University of Zilina, Slovakia

This paper deals with the non-destructive evaluation of surface made of roll bearing steel 100Cr6 after milling cycles via Barkhausen noise technique. The paper discusses magnetic anisotropy linked with the structure transformations with regard to variable flank wear of cutting tool. Effective value of Barkhausen noise (BN), Peak Position and Full Width at Half Maximum (FWHM) derived from the raw BN signals are compared with metallographic observations and residual stress profiles. Surface integrity is also expressed in term of surface roughness due to comparable BN sensitive layer and the height of surface roughness profile.

Keywords: Barkhausen noise; milling; surface integrity

Published: August 31, 2015  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Neslusan, M., Hrabovsky, T., Cillikova, M., & Micietova, A. (2015). Barkhausen Noise Emission in Milled Surfaces. Communications - Scientific Letters of the University of Zilina, 17(3), 57-61. doi: 10.26552/com.C.2015.3.57-61
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. KAMEDA, J., RANJAN, R.: Nondestructive Evaluation of Steels using Acoustic and Magnetic Barkhausen Signals - II. Effect of Intergranular Impurity Segregation, Acta Metall., vol. 35/7 1987, pp. 1527-1531. Go to original source...
    2. BUTTLE, D. J., SCRUBY, C. B., JAKUBOVICS, J. P., BRIGGS, G. A. D.: Magneto-acoustic and Barkhausen Emission: Their Dependence on Dislocations in Iron, NDT & E Int., vol. 24 1991, pp.47-54. Go to original source...
    3. GATELIER-ROTHEA, C., et al.: Characterization of Pure Iron and Carbon-iron Binary Alloy by Barkhausen Noise Measurements: Study of the Influence of Stress and Microstructure, Acta Mater., vol. 46/14, 1998, 4873-4882. Go to original source...
    4. RANJAN, R., JILES, D.C., RASTOGI, P.: Magnetic Properties of Decarburized Steels: An Investigation of the Effects of Grain Size and Carbon Content, IEEE Trans. Magn., vol. 23/3, 1987, 869-1876. Go to original source...
    5. BARKHAUSEN, H.: Phys. Zeitschrift, vol. 20, 1919, pp. 201.
    6. MICUCH, M., CILLIKOVA, M., NESLUSAN, M., MICIETOVA, A.: Micromagnetic Study of Cutting Conditions and Grinding Wheel Wear Influence on Surface Integrity, Manufacturing Technology, vol. 14 2014, 66-71. Go to original source...
    7. ROSIPAL, M.: Application of Barkhausen Noise for Study of Surface Integrity of Machined Surfaces, PhD. Dissertation, University of Zilina, 2012.
    8. CIZEK, J., NESLUSAN, M. CILLIKOVA, M., MICIETOVA, A. MELIKOVA, O.: Modification of Steel Surfaces Induced by Turning: Non-destructive Characterization using Barkhausen Noise and Positron Annihilation, J. of Physics D: Applied Physics, vol. 47, 2014, 1-17. Go to original source...
    9. DUBEC, J., NELUSAN, M., FAKTOR, M.: Analysing the Influence of Tool Wear when Turning, on Bearing Rings Deformation through Barkhausen Noise, Technolog, vol. 1, 2013, 16-21.
    10. NECKAR, F.: Influence of Cutting Process on Surface Integrity, Research report No. 400, CVUT : Praha, 1985.
    11. HAJKO, V., POTOCKY, L., ZENTKO, A.: Magnetization Processes, ALFA : Bratislava, 1982.
    12. DUBEC, J., NESLUSAN, M.: Multiparametric Analysis of Surface after Turning through Barkhausen Noise in Relation to Tool Wear, MM Science, July 2012. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content