Communications - Scientific Letters of the University of Zilina 2022, 24(1):B9-B19 | DOI: 10.26552/com.C.2022.1.B9-B19

Dynamic Modelling of Piston the Motion in Combustion Engines

Sunny Narayan ORCID...1, Shitu Abubakar ORCID...2, Muhammad Usman Kaisan ORCID...2, Hauwa Ndagi2, Yunusa Tukur3, Ivan Grujię ORCID...4, Nadica Stojanovię ORCID...4
1 Mechanical Engineering Department, Qassim University, Burydah, Saudi Arabia
2 Mechanical Engineering Department, Ahmadu Bello University, Zaria, Nigeria
3 Department of Energy Planning and Analyses, Energy Commission of Nigeria, Abuja, Nigeria
4 Department of Motor Vehicles and Motors, University of Kragujevac, Kragujevac, Serbia

The presented work discusses a methodology for analysis of noise emissions from a diesel engine. A numerical model of the piston motion, analyzing its lateral, reciprocating and rotation motion, has been presented in order to investigate the lateral motion of the piston skirt assembly and resulting vibrations induced as a result of these motions in the engine block. Various parameters of modal analysis were obtained using the mobility analysis. The presented methodology was validated by data obtained from a diesel engine test set up. The predicted results matched well with those of measured data, hence validating the presented scheme.

Keywords: acoustics, vibrations, noise, piston motion

Received: March 17, 2021; Accepted: June 2, 2021; Prepublished online: September 30, 2021; Published: January 1, 2022  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Narayan, S., Abubakar, S., Kaisan, M.U., Ndagi, H., Tukur, Y., Grujię, I., & Stojanovię, N. (2022). Dynamic Modelling of Piston the Motion in Combustion Engines. Communications - Scientific Letters of the University of Zilina, 24(1), B9-19. doi: 10.26552/com.C.2022.1.B9-B19
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. WANNATONG, K., CHANCHAONA, S., SANITJAI, S. Simulation algorithm for piston ring dynamics. Simulation Modelling Practice and Theory [online]. 2008, 16(1), p. 127-146. ISSN 1569-190X. Available from: https://doi.org/10.1016/j.simpat.2007.11.004 Go to original source...
    2. FLORES, P., AMBROSIO, A., CLARO, J., LANKARANI, H. Translational joints with clearance in rigid multibody systems. Journal of Computational and Nonlinear Dynamics [online]. 2008, 3(1), 011007. ISSN 1555-1415, eISSN 1555-1423. Available from: https://doi.org/10.1115/1.2802113 Go to original source...
    3. HAN, D.-CH., LEE, J.-S. Analysis of the piston ring lubrication with a new boundary condition. Tribology International [online]. 1998, 31, p. 753-760. ISSN 0301-679X. Available from: https://doi.org/10.1016/S0301-679X(98)00096-6 Go to original source...
    4. RAHNEJAT, H., BALAKRISHNAN, S., KING, P., HOWELL-SMITH, S. In-cylinder friction reduction using a surface finish optimization technique. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering [online]. 2006, 220(9), p. 1309-1318. ISSN 0954-4070, eISSN 2041-2991. Available from: https://doi.org/10.1243/09544070JAUTO282 Go to original source...
    5. CHO, S. H., AHN, S. T., KIM, Y. H. A simple model to estimate the impact force induced by piston slap. Journal of Sound and Vibration [online]. 2002, 255(2), p. 229-242. ISSN 0022-460X. Available from: https://doi.org/10.1006/jsvi.2001.4152 Go to original source...
    6. ZHANG, Z., XIE, Y., ZHANG, X., MENG, X. Analysis of piston secondary motion considering the variation in the system inertia. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering [online]. 2009, 223(4), p. 549-563. ISSN 0954-4070, eISSN 2041-2991. Available from: https://doi.org/10.1243/09544070JAUTO1078 Go to original source...
    7. FLORES, P., LEINE, R., GLOCKER, C. Modeling and analysis of planar rigid multibody systems with translational clearance joints based on the non-smooth dynamics approach. Multibody System Dynamics [online]. 2010, 23, p. 165-190. ISSN 1384-5640, eISSN 1573-272X. Available from: https://doi.org/10.1007/s11044-009-9178-y Go to original source...
    8. FARAHANCHI, F., SHAW, S. W. Chaotic and periodic dynamics of a slider-crank mechanism with slider clearance. Journal of Sound and Vibration [online]. 1994, 177(3), p. 307-324. ISSN 0022-460X. Available from: https://doi.org/10.1006/jsvi.1994.1436 Go to original source...
    9. MCFADDEN, P., TURNBULL, S. Dynamic analysis of piston secondary motion in an internal combustion engine under non-lubricated and fully flooded lubricated conditions. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science [online]. 2011, 225(11), p. 2575-2585. ISSN 0954-4062, eISSN 2041-2983. Available from: https://doi.org/10.1177/0954406211408674 Go to original source...
    10. GENG, Z., CHEN, J. Investigation into piston-slap-induced vibration for engine condition simulation and monitoring. Journal of Sound and Vibration [online]. 2005, 282(3-5), p. 735-751. ISSN 0022-460X. Available from: https://doi.org/10.1016/j.jsv.2004.03.057 Go to original source...
    11. OFFNER, G., HERBST, H. M., PRIEBSCH, H. H. A methodology to simulate piston secondary movement under lubricated contact conditions. In: SAE 2001 World Congress: proceedings [online]. USA: SAE International, 2001. ISSN 0148-7191, eISSN 2688-3627, technical paper 2001-01-0565. Available from: https://doi.org/10.4271/2001-01-0565 Go to original source...
    12. LIU, K., XIE, Y., GUI, C. A comprehensive study of the friction and dynamic motion of the piston assembly. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology [online]. 1998, 212(3), p. 221-226. ISSN 1350-6501, eISSN 2041-305X. Available from:https://doi.org/10.1243/1350650981542038 Go to original source...
    13. KIM, T. J. Numerical analysis of the piston secondary dynamics in reciprocating compressors. Journal of Mechanical Science and Technology. 2003, 17(3), p. 350-356. ISSN 1738-494X, eISSN 1976-3824. Go to original source...
    14. RUGGIERO, A., SENATORE, A. Computer model for the prediction of the impact force induced by piston slap in internal combustion engines, The Annals of the University Dunarea de Jos of Galati, Fascicle VIII: Tribology [online]. 2003, 2003, p. 129-134. ISSN 1221-4590.
    15. DESAI, H. Computer aided kinematic and dynamic analysis of a horizontal slider crank mechanism used for single-cylinder four stroke internal combustion engine. In: World Congress on Engineering WCE 2009: proceedings [online]. Vol. II. 2009. ISBN 978-988-18210-1-0, p. 1-3.
    16. WILSON, R., FAWCETT, J. N. Dynamics of the slider-crank mechanism with clearance in the sliding bearing. Mechanism and Machine Theory [online]. 1974, 9(1), p. 61-80. ISSN 0094-114X. Available from: https://doi.org/10.1016/0094-114X(74)90008-1 Go to original source...
    17. HADDAD, S. D., TJAN, K. T. An analytical study of offset piston and crankshaft designs and the effect of oil film on piston slap excitation in a diesel engine. Mechanism and Machine Theory [online]. 1995, 30(2), p. 271-284.ISSN 0094-114X. Available from:https://doi.org/10.1016/0094-114X(94)00035-J Go to original source...
    18. KOIZUMI, T., TSUJIUCHI, N., OKAMURA, M., TSUKIJIMA, H., KUBOMOTO, I., ISHIDA, E. Reduction of piston slap excitation by optimizing piston profiles. In: SPIE 2002: proceedings [online]. 2002. p. 107-113.
    19. JANG, S., CHO, J. Effects of skirt profiles on the piston secondary movements by the lubrication behaviors. International Journal of Automotive Technology. 2004, 5(1), p. 23-31. ISSN 1229-9138, eISSN 1976-3832.
    20. NARAYAN, S. Effects of various parameters on piston secondary motion. In: 18th Asia Pacific Automotive Engineering Conference: proceedings [online]. USA: SAE International, 2015. ISSN 0148-7191, eISSN 2688-3627, technical paper 2015-01-0079. Available from: https://doi.org/10.4271/2015-01-0079. Go to original source...
    21. GUZZOMI, A., HESTERMAN, D., STONE, B. Variable inertia effects of an engine including piston friction and a crank or gudgeon pin offset. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering [online]. 2008, 222(3), p. 397-414. ISSN 0954-4070, eISSN 2041-2991. Available from: https://doi.org/10.1243/09544070JAUTO590 Go to original source...
    22. GUZZOMI, A., HESTERMAN, D., STONE, B. The effect of piston friction on engine block dynamics. Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-body Dynamics [online]. 2007, 221(2), p. 277-289. ISSN 1464-4193, eISSN 2041-3068. Available from: https://doi.org/10.1243/14644193JMBD66 Go to original source...
    23. GERGES, S. N. Y., DE LUCA, J. C., LALOR, N. The influence of cylinder lubrication on piston slap. Journal of Sound and Vibration [online]. 2002, 257(3), p. 527-557. ISSN 0022-460X. Available from: https://doi.org/10.1006/jsvi.2002.5051 Go to original source...
    24. TAN, Y. C., RIPIN, Z. Technique of measuring piston secondary motion using laser displacement sensors. Experimental Mechanics [online]. 2012, 52, p. 1447-1459. ISSN 0014-4851. Available from: https://doi.org/10.1007/s11340-012-9600-x Go to original source...
    25. COMFORT, A. An introduction to heavy-duty diesel engine frictional losses and lubricant properties affecting fuel economy - Part I. SAE International [online]. 2003, 2003-01-3225. ISSN 0148-7191, eISSN 2688-3627. Available from:https://doi.org/10.4271/2003-01-3225 Go to original source...
    26. TAYLOR, R., COY, R. Improved fuel efficiency by lubricant design: A review. Proceedings of the Institution of Mechanical Engineers: Part J: Journal of Engineering Tribology [online]. 2000, 214(1), p. 1-15. ISSN 1350-6501, eISSN 2041-305X. Available from: https://doi.org/10.1177/135065010021400101 Go to original source...
    27. ZWEIRI, Y., WHIDBORNE, J., SENEVIRATNE, L. Instantaneous friction components model for transient engine operation. Proceedings of the Institution of Mechanical Engineers: Part D: Journal of Automobile Engineering [online]. 2002, 214, p. 809-824. ISSN 0954-4070, eISSN 2041-2991. Available from: https://doi.org/10.1243/0954407001527664 Go to original source...
    28. TAN, Y. C., RIPIN, Z. M. Frictional behavior of piston rings of small utility two-stroke engine under secondary motion of piston. Tribology International [online]. 2011, 44(5), p. 592-602. ISSN 0301-679X. Available from: https://doi.org/10.1016/j.triboint.2010.12.009 Go to original source...
    29. SHI, X., POLYCARPOU, A. A. Measurement and modeling of normal contact stiffness and contact damping at the meso scale. Journal of Vibration and Acoustics [online]. 2005, 127(1), p. 52-60. ISSN 1048-9002, eISSN 1528-8927. Available from: https://doi.org/10.1115/1.1857920 Go to original source...
    30. CAWLEY, P., CLAYTON, D. A vibration technique for the measurement of contact stiffness. Mechanical Systems and Signal Processing [online]. 1987, 1(3), p. 273-283. ISSN 0888-3270. Available from: https://doi.org/10.1016/0888-3270(87)90104-X Go to original source...
    31. HIXSON, E. L. Mechanical impedance. In: Harris' shock and vibration handbook. HARRS, C. M., PIERSOL, A. G. (eds). New York: McGraw-Hill, 1988. ISBN 0-07-137081-1.
    32. HYNNA, P. Mechanical mobility technique [online]. Research report no. BVAL37-021228. Espoo: VTT Technical Research Centre of Finland, 2002. Available from: http://www.vtt.fi/inf/julkaisut/muut/2002/BVAL37-021228.pdf
    33. MITTLER, R., MIERBACH, A., RICHARDSON, D. Understanding the fundamentals of piston ring axial motion and twist and the effects on blow-by. In: ASME 2009 Internal Combustion Engine Division Spring Technical Conference: proceedings [online]. 2009, ICES2009:76080. ISBN 978-0-7918-4340-6, p. 721-735. Available from: https://doi.org/10.1115/ICES2009-76080 Go to original source...
    34. TAKIGUCHI, M., ANDO, H., TAKIMOTO, T., URATSUKA, A. Characteristics of friction and lubrication of two-ring piston. JSAE Review [online]. 1996, 17(1), p. 11-16. ISSN 0389-4304. Available from: https://doi.org/10.1016/0389-4304(95)00050-X Go to original source...
    35. XIAO, S., YAN, F., LU, CH., LU, Z. Optimization design of piston structure for abnormal noise control in a single-cylinder gasoline engine. Advances in Mechanical Engineering [online]. 2018, 10, p. 1-16. ISSN 1687-8140, eISSN 1687-8140. Available from: https://doi.org/10.1177/1687814018769407 Go to original source...
    36. NARAYAN, S., GUPTA, V. Numerical analysis of secondary motion of piston skirt in engines. International Journal of Acoustics and Vibrations. 2018, 23(4), p. 557-565. ISSN 1027-5851, eISSN 2415-1408.
    37. NARAYAN, S. Analysis of piston slap motion. International Journal of Applied Mechanics and Engineering [online]. 2015, 20(2), p. 445-450. eISSN 2353-9003. Available from: https://doi.org/10.1515/ijame-2015-0030 Go to original source...
    38. NARAYAN, S. Piston slap noise in engines. International Journal of Applied Engineering Research. 2015, 8(14), p. 1695-1700. ISSN 0973-4562, eISSN 0973-9769.
    39. MAHROOGI, F., NARAYAN, S. Dynamic-analysis-of-piston-secondary-motion-using FEM method. In: 26th International Congress on Sound and Vibration: proceedings. 2019. ISSN 2329-3675, ISBN 978-1-9991810-0-0.
    40. KAISAN, M. U., YUSUF, L. O., IBRAHIM, I. U., ABUBAKAR, S., NARAYAN, S. Effects of propanol and camphor blends on emissions and performance of a spark ignition engine. American Chemical Society (ACS) Omega [online]. 2020, 5(41), p. 26454-26462. ISSN 2470-1343. Available from: https://doi.org/10.1021/acsomega.0c02953 Go to original source...
    41. GRUJIC, I., STOJANOVIC, N., PESIC, R., DAVINIC, A., NARAYAN, S. Numerical analysis of IC engine operation with high pressure hydrogen injections. Transactions of FAMENA [online]. 2020, 44(1), p. 55-56. ISSN 1333-1124, ISSN 1849-1391. Available from: https://doi.org/10.21278/TOF.44105 Go to original source...
    42. MAHROOGI, F. O., NARAYAN, S. A recent review of hybrid automotive systems in GCC region. Proceedings of Institute of Mechanical Engineers Part D: Journal of Automotive Engineering [online]. 2019, 233(14), p. 1393-1402. ISSN 0954-4070, eISSN 2041-2991. Available from: https://doi.org/10.1177/0954407019836055 Go to original source...
    43. ABUBAKAR, S., ANAFI, F. O., KAISAN, M. U., NARAYAN, S., UMAR, S., UMAR, U. A. Comparative analysis of experimental and simulated performance of a mixed mode solar dryer. Proceedings of Institute of Mechanical Engineers Part C: Journal of Mechanical Engineering [online]. 2019, 234(7), p. ISSN 0954-4062, eISSN 2041-2983. Available from: https://doi.org/10.1177/0954406219893394 Go to original source...
    44. KAISAN, M. U., ABUBAKAR, S., ASHOK, B., BALASUBRAMANIAN, D., NARAYAN, S., GRUJIC, I., STOJANOVIC, N. Comparative analyses of biodiesel produced from Jatropha and neem seed oil using a gas chromatography mass spectroscopy technique. Biofuels [online]. 2018, lates articles. ISSN 1759-7269, eISSN 1759-7277. Available from: https://doi.org/10.1080/17597269.2018.1537206 Go to original source...
    45. NARAYAN, S. A review of diesel engine acoustics. FME Transactions [online]. 2014, 42(2), p. 150-154. ISSN 1451-2092, eISSN 2406-128X. Available from: https://doi.org/10.5937/fmet1402150N Go to original source...
    46. NARAYAN, S., MILOJEVIC, S., GUPTA, V. Combustion monitoring in engines using accelerometer signals. Journal of Vibroengineering [online]. 2019, 21(6), p. 1552-1563. ISSN 1392-8716, eISSN 2538-8460. Available from: https://doi.org/10.21595/jve.2019.20516 Go to original source...
    47. MAHROOGI, F. O., NARAYAN, S., GUPTA, V. Acoustic transfer function in gasoline engines. International Journal of Vehicle Noise and Vibration (IJVNV) [online]. 2018, 13(3), p. 270-280. ISSN 1479-1471, eISSN 1479-148X. Available from: https://doi.org/10.1504/IJVNV.2018.097212 Go to original source...
    48. NARAYAN, S. Wavelet analysis of diesel engine noise. Journal of Engineering and Applied Sciences [online]. 2013, 8(8), p. 255-259.ISSN 1816-949x, eISSN 1818-7803. Available from: https://doi.org/10.36478/jeasci.2013.255.259 Go to original source...
    49. NARAYAN, S. Effect of dwell time on noise radiated from diesel engine. International Journal of Applied Engineering Research. 2013, 8(11), p. 1339-1347. ISSN 0973-4562, eISSN 0973-9769.
    50. MUHAMMED, M. M., KAISAN, M. U., ABUBAKAR, S., NARAYAN, S. Determination of wear metals debris concentration in aircraft engines. International Journal of Innovative Technology and Exploring and Engineering (IJITEE). 2019, 8(11), p. 1289-1292 eISSN 2278-3075. Go to original source...
    51. NARAYAN, S., ALSAGRI, A. S., GUPTA, V. Design and analysis of hybrid automotive suspension system. International Journal of Mechanical and Production Engineering Research and Development (IJMPERD)[online]. 2019, 9(4), p. 637-642. ISSN 2249-6890, eISSN 2249-8001. Available from: https://doi.org/10.24247/ijmperdaug201963 Go to original source...
    52. MAHROOGI, F. O., NARAYAN, S. Design and analysis of double wishbone suspension systems for automotive applications. International Journal of Mechanical and Production Engineering Research and Development (IJMPERD) [online]. 2019, 9(4), p. 1433-1442. ISSN 2249-6890, eISSN 2249-8001. Available from: https://doi.org/10.24247/ijmperdaug2019148 Go to original source...
    53. STOJANOVIC, N., GLISOVIC, J., GRUJIC, I., NARAYAN, S. Influence of size of ventilated brake disc ribs on air flow velocity. International Journal of Advanced Science and Technology(IJAST) [online]. 2020, 29(1), p. 637-647.ISSN 2005-4238, eISSN 2207-6360. Available from: http://sersc.org/journals/index.php/IJAST/article/view/3285
    54. MAHROOGI, F. O., NARAYAN, S. Effects of dampers on piston slapping motion. International Journal of Vehicle Noise and Vibration (IJVNV) [online]. 2020, 16(1/2), p. 46-57. ISSN 1479-1471, eISSN 1479-148X. Available from: https://doi.org/10.1504/IJVNV.2020.112432 Go to original source...
    55. NARAYAN, S., GUPTA, V. Frequency characteristics of in cylinder pressure of a gasoline engine. Journal of Applied Engineering Science [online]. 2021, 19(1), p. 92-97. ISSN 1451-4117, eISSN 1821-3197. Available from: https://doi.org/10.5937/jaes0-27156 Go to original source...
    56. NARAYAN, S. Modelling of noise radiated from engines. In: The 11th International Conference on Automotive Engineering: proceedings [online]. 2015. 2015-01-0107. ISSN0148-7191, eISSN 2688-3627. Available from: https://doi.org/10.4271/2015-01-0107 Go to original source...
    57. NARAYAN, S. Analysis of noise emitted from diesel engines. Journal of Physics: Conference Series [online]. 2015, 662, 012018. ISSN 1742-6588, eISSN 1742-6596. Available from: https://doi.org/10.1088/1742-6596/662/1/012018 Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content